Zapamiętaj mnie


Odpowiedz 
 
Ocena wątku:
  • 0 Głosów - 0 Średnio
  • 1
  • 2
  • 3
  • 4
  • 5
Magnifying glaas door installation steps
Autor Wiadomość
ahwhglass
Junior Member
**


Status: Offline
Liczba postów: 10
Dołączył: 21.05.2018
Post: #1
Magnifying glaas door installation steps
A thick glass door may be a decorative door with the thickness of 12 mm or over. It is generally composed of two parts: the movable fan and the fixed glass. The door frame is divided into stainless, copper and aluminum metal. 1 Before the design is completed, check whether the elevation in the ground and the height on the structure at the top on the door frame meet the planning requirements. Determine the position from the door frame and easy methods to install the glass. Choose the glass as outlined by the design requirements. Done profile door frame, restrict groove, plate and a glass glue, floor spring, fire wood screw, self-tapping screw along with auxiliary materials.
2 Installation points associated with fixed door frame coarse glass (1) Release and positioning Based on the design requirements, the position from the door frame is introduced, and the fixed along with movable part installation control lines are determined.
(2) The width in the stainless steel limit groove limit groove within the top of the installation door frame should be greater than the glass thickness of 2~4mm, along with the groove depth is 10~20mm.
(3) Install the stainless steel veneer on the yard first, then glue the stainless steel panel to the wood made side. The aluminum alloy square tube is often fixed on the frame column with an metal corner code, or can be fixed on the embedded embedded part by screws.
(4) Cut glass (usually pre-cut, then tempered and transported to the site for installation). The dimensions belonging to the bottom, middle and top from the actual volume should become measured, and the cut size from the minimum size of the glass width need to be selected. If the dimensions measured inside upper, middle and lower would be the same, the size can be cut, the width is not as much as the measured size of 2-3 mm, and the height is less than Less than six mm. For the reduce glass, the chamfered edging shall be carried out on the actual four sides by hand-held oil-coated gemstone, with a chamfer size of 2 mm.
(5) Install the glass using a colored Laminated glass suction cup to lift the thick tumbler up, insert the thick glass plate in the limit groove at the most notable of the door figure, and then place it to the bottom bracket so the edge of the coarse glass plate just seals the side. The stainless steel trim on the frame column faces this seam.
(6) The glass is fixed on the bottom bracket and that pressure clamp strip is installed, about 4mm from the thick glass registration. Then apply the universal glue to the strip and stick the metal plate on the strip.
(7) Inject the glass seal towards top limit groove and also the bottom support, and inject the glass glue on the joint between the thick glass plus the frame column, so which the glass glue forms your uniform straight line on the gap. Finally, scrape heli-copter flight excess glass glue along with wipe the glue with a clean cloth. When thick glass is butted, the joint should be kept at a mileage of 2~3mm. The thick glass edge ought to be chamfered. After the two thick glass are positioned and fixed, the glass glue is used to inject into this gap. After filling, your thick glass is loaded. Squeeze the glass glue in both sides and wipe the glue using a clean cloth.
3 The installation point with the movable door leaf thicker glass The thick magnifying glaas movable door leaf features no door frame. The opening and closing from the movable door leaf is realized by hardware hinged to top of the and lower rails on the frame.
(1) Floor spring mounting ground spring is surely an automatic door closing machine installed under various home fans.
(2) Mark top of the and lower rails in the door leaf, and fix the pin hole plate of the rotation pin and the rotation shaft connection plate belonging to the floor spring by your wire. Refer to the installation instructions emotionally involved with the ground spring solution for installation.
(3) Drill the holes while in the door handle (usually instructed to be processed when acquiring thick glass). Note the height dimension of the actual thick glass should add the mounting portion that is inserted into the upper and lower track. Usually the cut width of thick glass ought to be less than about 5mm with measurement size for resetting.
(4) Install the top and lower rails for the upper and lower sides of the thick glass door and also measure the height from the door. If the upper and lower edges in the door leaf are not likely the specified value inside gap between the door frame along with the ground, the wooden splint might be placed under the glass while in the upper and lower track. If the door leaf peak exceeds the installation sizing, the excess portion from the thick glass door leaf is required to be cut.
(5) After setting up the height, fix top of the and lower rails. For the gap between the thick glass and also the metal upper and lower rails, a small wooden strip is inserted as well, and then the tumbler glue is injected on the gap between the little wooden strip, the thick glass along with the crosspiece.
(6) Door admirer positioning installation. First, adjust the positioning pin for the door frame beam featuring its own adjustment screw towards beam plane 1~2mm. Next erect the glass entry leaf, align the hole position belonging to the rotating pin connector on the lower crosspiece of the door leaf when using the rotation pin of the spring, and turn the door leaf to suit the hole into that pin. Then, with the pin axis because the axis, turn the door leaf 90° (to right the door leaf any time turning), so that the door leaf and the door beam are with right angles. At this time around, the hole of the rotating connecting piece from the crosspiece of the door leaf might be aligned on the door frame beam. The positioning pin is turned out and the positioning pin is turned out, and inserted into the hole in the door leaf cross-rotating pin connecting member is all about 15 mm. Install your glass door handle. In advance of installation, apply a tiny amount of glass glue to the part the place that the handle is inserted to the glass. When the deal with is assembled, the root is closely mounted on the glass, and then the mending screw is tightened to make certain the handle is not loose.
17.12.2018 3:03
Znajdź wszystkie posty użytkownika Odpowiedz cytując ten post
Odpowiedz 


Skocz do:


Użytkownicy przeglądający ten wątek: 2 gości

Kontakt | Autoxen.pl | Wróć do góry | Wróć do forów | Wersja bez grafiki | RSS